Mar 04, 2014  Como apagar resetear la luz SRS o de bolsa de aire en Honda Civic, Accord, CR-V, Acura, Element, Pilot, CL, RSX, Logo, Insight, GS, GSR 97 98 99 00 01 02 03. Home 2008 Toyota Highlander Rear Suspension. Rear Suspension for 2008 Toyota Highlander. Toyota Parts Express. Jun 16, 2010  ford explore 2002 reparacion de vidrio o ventana electrica. TOYOTA HIGHLANDER DOOR PANEL REMOVAL AND SET WINDOW BACK. REPARA LOS ELEVADORES DE TU AUTO POR SOLO $15 // NISSAN B-12.

1. Toyota Highlander Used
2. La Suspension De Atras Toyota Highlander 2008 Manual Partes En

Select Your Front Suspension Front Suspension Parts for 2008 Toyota Highlander Base. Front Suspension/Front Suspension for 2008 Toyota Highlander. Toyota Parts; Toyota Auto Parts Tell Us More About Your Toyota. View all makes AutoZone carries hundreds of thousands of parts and accessories. Select your Year, Make, Model and Engine to find those that fit your vehicle. See all in Toyota Suspension, Steering, Tire And Wheel. Toyota Shock/Strut - Front. Hola necesito el manual del diagrama de las cadenas de tiempo de toyota avanza 2008 1.3 porfavor. Jorge luis cabrales hernandez said. O manual de partes de piezas del toyota tercel twin cam. Desde ya muchas gracias. Necesito el diagrama de la suspension trasera del honda civic 2000 exr 4 ptas para poder ver los bujes y poder. Gracias por entrar a la pagina web de mst recycling, aqui usted encontrara todas las partes usadas I nuevas que necesite para cualquier mitsubish oi toyota o saturn ya sea camioneta auto o suv, cualquier pregunta, consulta o si desea ordenar una parte porfavor comuniquese con Richard: 800-695-4700 Richard.

ADJUSTMENT

1. INSPECT TIRE (SEE PAGE 26-7 )

2. MEASURE VEHICLE HEIGHT

Vehicle height:

Measuring points:

A: Ground clearance of front wheel center B: Ground clearance of lower suspension arm No.2 bush set bolt center
C: Ground clearance of strut rod set bolt center D: Ground clearance of rear wheel center

NOTICE: Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

HINT: Bounce the vehicle at the corners up and down to stabilize the suspension and inspect the vehicle height.

3. INSPECT TOE-IN

Toe-in:

If the toe-in is not within the specified range, adjust it at the rack ends.

4. ADJUST TOE-IN

(Turbo/AWD)The engine specs; 224 whp/298 NmUsed the stock gearbox of RS Cosworth adding only a 6th gear.The car is in Escort RS Cosworth colors + additional 4 special colors.The setup is adjustable.I hope you like the both versions. Stock and tuned.STOCK:As usual, suitable to real car’s factory defaults.Colors, wheels, engine and drivetrain specs are the same as the real car.Engine and drive train specs; 84 whp/122 Nm, 4 speed gearbox with 3.583 final gear.TUNED:Body modifiedThe rear suspension has been converted to McPherson from Axle.Sport physic setupEquipped with a stock Escort RS Cosworth Engine and drive train. This mod consists of two versions.

(a) Remove the rack boot set clips.

(b) Loosen the tie rod end lock nuts.

(c) Turn the right and left rack ends by equal amounts to adjust the toe-in.

HINT: Try to adjust the toe-in to the center of the specified value.

Toyota Highlander Used

(d) Make sure that the lengths of the right and left rack ends are the same.

Rack and length difference: 1.5 mm (0.059 in.) or less (e) Torque the tie rod end lock nuts.

Torque: 74 N*m (755 kgf*cm, 55 ft*lbf) (f) Place the boots on the seats and install the clips.

HINT: Make sure that the boots are not twisted.

(g) Perform VSC system calibration (see page 05-765 ).

5. INSPECT WHEEL ANGLE

(a) Turn the steering wheel fully left and right to measure the turning angle.

Wheel turning angle:

If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.

6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

(a) Put the front wheel on the center of the alignment tester.

(b) Set the camber - caster - kingpin gauge at the center of the axle hub or drive shaft.

Camber, caster and steering axis inclination:

La Suspension De Atras Toyota Highlander 2008 Manual Partes En

If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and/or wear.

7. ADJUST CAMBER

NOTICE: Inspect toe-in after the camber has been adjusted.

(a) Remove the front wheel.

(b) Remove the 2 nuts on the lower side of the shock absorber.

HINT: When removing the nuts, keep the bolts from rotating.

(c) Clean the installation surface of the shock absorber and the steering knuckle.

(d) Temporarily install the 2 nuts.

(e) Fully push or pull the front axle hub in the direction of the required adjustment.

(f) Tighten the nuts.

Torque: 230 NVm (2,350 kgfVcm, 170 ftVlbf) HINT: When installing the nuts, keep the bolts from rotating and then torque the nuts.

(g) Install the front wheel.

Torque: 103 N*m (1,050 kgf*cm, 76 ft*lbf)

NOTICE: Keep the bolts from rotating and torque the nuts.

(h) Install the front wheel.

Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf) (i) Check the camber.

If the measured value is not within the specified range, calculate the required adjustment amount using the formula below.

(Camber adjustment amount) = Center of the specified range medium - Measured value

Check installed bolts combination. Select appropriate bolts from the table below to adjust the camber to within the specified range.

Table (1) (Move the axle toward positive side)

Selected Bolt Combination

Bolt Distinguishing Mark

The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.

NOTICE: Replace the nut with a new one when replacing the bolt.

(j) Repeat the steps mentioned above. At step (b), replace 1 or 2 selected bolts.

HINT: Replace one bolt at a time when replacing 2 bolts.

Table (2) (Move the axle toward negative side)

Selected Bolt Combination

Bolt Distinguishing Mark

The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.

NOTICE: Replace the nut with a new one when replacing the bolt.

(k) Repeat the steps mentioned above. At step (b), replace 1 or 2 selected bolts.

HINT: Replace one bolt at a time when replacing 2 bolts.

More about Toyota Highlander:

Washer fluid
If any washer does not work or the warning message appears on the multi-information display, the washer tank may be empty. 2002 mazda mpv service repair manual cd torrent free download movies. Add washer fluid. Warning When adding washer fluid Do not add washer fluid when the engine is hot or running as washer fluid contains alcohol and ma ..