' Ford Error Codes 'download

  1. Ford Error Code P0430
  2. Microsoft Error Codes
  3. Ford Error Codes P0401
  4. Error Code List
  5. Ford Error Codes Sensor Circuit
Ford

OBDII Ford Code Definitions. Be sure to double check the codes. Anything P1000 to P1999 or P3000 to P3400 will be Manufacturer specific and may not match the ones listed here. OBD-II (Check Engine Light) Trouble Codes. Welcome to OBD-Codes.com, your headquarters for everything OBD-II related. For more information on what OBD codes are, OBD-II codes explained, explanation of fuel trims, or answers to other questions, visit our FAQ area.

Ford DTC's (Diagnostic Trouble Codes)

Data Link Connector (DLC)(Located Under hood)

Analog Voltmeter Connection

Ford Codes

11System PASS.
12Cannot control rpm during KOER Sell-Test high rpm check.
13Cannot control rpm during KOER Self-Test low rpm check.
14PIP Circuit failure.
15PCM Read Only Memory (ROM) teat failed.
16Rpm too low to perform H02S test.
18SPOUT circuit open.
18IDM circuit failure/ SPOUT circuit grounded.
19Failure In PCM Internal voltage.
21ECT out of Self-Test range MAP/BARO out of Self-Test range.
22MAP/BARO out of Self-Test range.
23TP out of Self-Test range.
24IAT out of Self-Test range.
26MAF out of Self-Test range.
29Insufficient input from the Vehicle Speed Sensor (VSS).
31EVP circuit below minimum voltage.
32EVP voltage below closed limit.
33EGR valve opening not detected.
34EVP voltage above closed limit.
35EVP circuit above maximum voltage.
41HO2S circuit indicates system lean (right HO2S).
41No HO2S switch detected (right HO2S).
42HO2S circuit indicates system rich (right HO2S).
44Secondary Air Injection system Inoperative (right side).
45Secondary Air Injection upstream during Self-Test.
46Secondary Air Injection not bypassed during Self-Test.
51ECT Indicated -40 C (-40 F) /circuit open.
53TP circuit above maximum voltage.
54IAT Indicated -4000 (-40'F) /circuit open.
56MAF circuit above maximum voltage.
61ECT Indicated 123 C (254 F) / circuit grounded.
63TP circuit below minimum voltage.
64IAT indicated 123 C (254 F) I circuit grounded.
66MAF circuit below minimum voltage.
67Park/Neutral Position (PNP) switch circuit open - A/C on during Self-Test.
77Brief WOT not sensed during Self-Test / Operator error.
79A/C on/Defrost on during Self-Test.
81Secondary -Air Injection Diverter (AIRD) solenoid circuit failure.
82Secondary Air Injection Bypass (AIRS) solenoid circuit failure.
84EGR Vacuum Regulator (EVR) circuit failure.
85Canister Purge (CANP) circuit failure.
87Fuel pump primary circuit failure.
91HO2S circuit Indicates system loan (left HO2S).
91No HO2S switch detected (left HO2S).
92HO2S circuit indicates system rich (left HO2S).
94Secondary Air Injection system Inoperative (left side).
95Fuel pump secondary circuit failure.

3 Digit Ford Codes

111

System checks OK

112

(O,M)

Intake Air Temperature (IAT) sensor is/was low or grounded - IAT

113

(O,M)

IAT sensor is/was high or open - IAT

114

(O,R)

IAT sensor out of range - IAT

116

(O,R)

Engine Coolant (ECT) sensor out of range - ECT

117

(O,M)

ECT sensor is/was low or grounded - ECT

118

(O,M)

ECT sensor is/was high or open - ECT

121

(O,R,M)

Throttle Position (TP) sensor out of range - TPS

122

(O,M)

TP low (possibly grounded or open circuit) - TPS

123

(O,M)

TP is/was high or short to power - TPS

124

(M)

TP voltage was higher than expected - Fuel control

125

(M)

TP voltage was lower than expected - Fuel control

126

(O,R,M)

MAP or BARO sensor out of range - '>MAP

128

(M)

MAP vacuum has not been changing - check vacuum lines - '>MAP

129

(R)

No MAP or Mass Air Flow sensor change during 'goose' test - MAP MAF

136

(R)

Oxygen sensor not switching/system lean Left or Front HO2S - Fuel control

137

(R)

Oxygen sensor not switching/system rich Left or Front HO2S - Fuel control

138

(R)

Fault in Cold Start Injector circuit - Fuel control

139

(M)

Oxygen sensor not switching Left or Front HO2S - Fuel control

144

(M)

Oxygen sensor not switching Single, Right or Rear HO2S - Fuel control

157

(R,M)

Mass Air Flow signal is/was low or grounded - MAF

158

(O,R,M)

MAF sensor is/was high or short to power - MAF

159

(O,R)

MAF sensor is/was out of range - MAF

167

(R)

No Throttle Position sensor change in 'goose' test (must get at least 25% rotation) - TPS

171

(M)

Oxygen sensor not switching - system was at adaptive limits - Single, Right or Rear HO2S - Fuel control

172

(R,M)

Oxygen sensor not switching - system is or was lean - Single, Right or Rear HO2S - Fuel control

173

(R,M)

Oxygen sensor not switching - system is or was rich - Single, Right or Rear HO2S - Fuel control

174

(M)

Oxygen sensor was slow in switching Single, Right or Rear HO2S - Fuel control

175

(M)

Oxygen sensor not switching - system was at adaptive limits - Left or Front HO2S - Fuel control

176

(M)

Oxygen sensor not switching - system is or was lean Left or Front HO2S - Fuel control

177

(M)

Oxygen sensor not switching - system was rich Left or Front HO2S - Fuel control

178

(M)

Oxygen sensor was slow in switching Left or Front HO2S - Fuel control

179

(M)

Fuel system was rich at part throttle Single, Right or Rear HO2S - Fuel control

181

(M)

Fuel system was lean at part throttle Single, Right or Rear HO2S - Fuel control

182

(M)

Fuel system was rich at idle Single, Right or Rear HO2S - Fuel control

183

(M)

Fuel system was lean at idle Single, Right or Rear HO2S - Fuel control

184

(M)

Mass Air (MAF) output higher than expected - Fuel control

185

(M)

Mass Air (MAF) output lower than expected - Fuel control

186

(M)

Injector pulse width longer than expected or Mass Air Flow (MAF) lower than expected - Fuel control

187

Injector pulse width shorter than expected or Mass Air Flow (MAF) higher than expected - Fuel control

188

(M)

Fuel system was rich at part throttle - Left or Front HO2S - Fuel control

189

(M)

Fuel system was lean at part throttle - Left or Front HO2S - Fuel control

191

(M)

Fuel system was rich at idle - Left or Front HO2S - Fuel control

192

(M)

Fuel system was lean at idle - Left or Front HO2S - Fuel control

193

Failure in Flexible Fuel (FF) sensor circuit - Fuel control

194

(M)

Perform cylinder balance test to check for inoperative injectors

195

(M)

Perform cylinder balance test to check for inoperative injectors

211

(M)

Ignition PIP signal was erratic or missing - Ignition Systems

212

(M)

Ignition TACH signal was erratic (module/wiring) or SPOUT circuit fault - Ignition Systems

213

(R)

Ignition SPOUT or SAW circuit open or shorted - Ignition Systems

214

(M)

Error in Cylinder ID (CID) circuit or signal - Ignition Systems

215

(M)

Primary circuit failure - ignition coil 1 - Ignition Systems

216

(M)

Primary circuit failure - ignition coil 2 - Ignition Systems

217

(M)

Primary circuit failure - ignition coil 3 - Ignition Systems

218

(M)

IDM signal open or high or left coil pack failure - Ignition Systems

219

(M)

SPOUT circuit failure, timing defaulted to 10 degrees - follow code 213 diagnosis

222

(M)

IDM open or high or right coil pack failure - Ignition Systems

223

(M)

Dual Plug (DPI), SPOUT or IDM circuit fault - Ignition Systems

224

(M)

Failure in ignition coil primary circuit - Ignition Systems

225

(R)

Knock sensor not tested (ignore if not pinging) - KS

226

(O)

Ignition Diagnostic Monitor (IDM) signal fault - Ignition Systems

232

(M)

EI primary coil circuit failure - Ignition Systems

238

(M)

EI primary circuit failure - ignition coil 4 - Ignition Systems

311

(R)

AIR system not working - Single, Right or Rear HO2S - Air Injection

312

(R)

AIR not diverting - Air Injection

313

(R)

AIR not bypassing - Air Injection

314

(R)

AIR inoperative, Left or Front HO2S - Air Injection

326

(R,M)

Pressure Feedback EGR shows low pressure EGR not seating or not seating intermittantly - PFE

327

(O,R,M)

EGR feedback signal is/was low - EVR or PFE

328

(O,R,M)

EGR Valve Position (EVP) is/was low - EVR

332

(R,M)

EGR did not open/respond during test or if memory code, did not open intermittantly - EVR or PFE

334

(O,R,M)

EVP sensor is/was high - EVR

335

(O)

EGR feedback signal is/was out of range - EVR or PFE

336

(O,R,M)

PFE sensor signal is/was was high - '>PFE

337

(O,R,M)

EGR feedback signal is/was was high - EVR

338

(M)

Cooling system did not heat up (check cooling system / thermostat operation)

339

(M)

Cooling system overheated (check cooling system / thermostat operation)

341

(O)

Octane jumper installed (information only code to notify you if it is installed)

411

(R)

Idle speed system not controlling idle properly (generally idle too high) - ISC

412

(R)

Idle speed system not controlling idle properly (generally idle too low) - ISC

452

(M)

Vehicle Speed Sensor (VSS) problem

511

(O)

No power to PCM pin 1 or bad PCM (processor)

512

(M)

Memory power (PCM pin 1) was interrupted - Was battery disconnected ?

513

(O)

Replace processor (PCM) (internal failure)

519

(O)

PSP switch/circuit open - PSP h Pedal Position (CPP) circuit fault - PNP

528

(M)

System shows voltage at pin 10 (is A/C on ?) or pin 30 (PNP, CPP switch) - PNP

529

(M)

Data Communications Link to processor failure Service any EEC codes, erase memory and retest If code is still present refer to instrument cluster diagnosis manual

533

(M)

Data Communications Link to instrument cluster failure - see 529

536

(O,R,M)

Brake On Off open or shorted to ground - BOO

538

(R)

System did not receive 'goose' test - TESTS

539

(O)

System shows voltage at PCM pin 10 Is A/C on ?

542

(O,M)

Fuel pump open, bad ground or always on - - Power / Fuel Pump Circuits

543

(O)

Fuel pump monitor circuit shows no power - Power / Fuel Pump Circuits

(M)

(Service 556 code first if present) Fuel pump relay or battery power feed was open - Power / Fuel Pump Circuits

551

Problem in Intake Manifold Runner Control (IMRC) solenoid/circuit - Solenoids

552

(O)

AIRB solenoid/circuit failure - Solenoids

553

(O)

AIRD solenoid/circuit failure - Solenoids

554

(O)

Fuel Press Regulator Control solenoid/circuit fault - Power / Fuel Pump Circuits

556

(O,M)

Fuel pump relay primary circuit fault - Power / Fuel Pump Circuits

557

(O,M)

Low speed pump relay primary circuit fault - Power / Fuel Pump Circuits

558

(O)

EGR vacuum regulator solenoid/circuit failure - EVR or PFE or Solenoids

559

(O)

A/C relay primary circuit fault - A/C and Fan Circuits

563

(O)

High Fan Control (HFC) circuit failure - A/C and Fan Circuits

564

(O)

Fan Control (FC) circuit failure - A/C and Fan Circuits

565

(O)

Canister Purge 1 solenoid/circuit failure - Solenoids

566

(O)

transmission 3/4 shift solenoid/circuit - Transmissions

569

(O)

Canister Purge 2 solenoid/circuit failure - Solenoids

578

(M)

A/C pressure sensor VREF short to ground - A/C and Fan Circuits

579

It's 4-digit code required for the re-activation of a Ford radio after a car power loss.You can unlock your Ford radio code in a few minutes on this site. It's easy and works for Fiesta, Focus, Transit and more.Created to prevent theft, this code has resulted in many more problems to the owners, since it is activated every time there is a loss of energy in the car. How To Unlock Ford Focus Radio Code. To complete this unlock Ford Focus radio code process successfully you just need to follow the rules that our team made for you. They offer you the online radio codes generator ready to start generating your Focus code at any time. Ford Focus Radio Code. On this page you will find information on how to generate the unlock code for the Ford Focus 6000CD radio for free. How to get an unlock code radio? To unlock the radio you need to know its serial number. It is located on the back of the radio so you will have to take it out. The serial number looks like this: M187803. Retrieving the code of your Ford Focus car is a piece of cake. All you need is the serial number of the radio (see how to find on this page). This radio code generator works for all years and models as well as for Ford Focus Mk1 and Mk2, C-max, Zetec, Titanium, LX, BJ and many others. Jun 17, 2017  If Ford vehicle battery disconnected. You’ll need to re-enter the radio security code. If you have lost your Ford radio code, you can recover it quickly and easily with Ford Radio Code. Ford Radio Code Free on Play Store. Find Ford serial number Case 1: Get Serial on Display. Turn on your radio and hold the preset buttons 1 and 6 for 3 seconds. Ford focus replacement radio

(M)

ACP sensor did not change with A/C on - A/C and Fan Circuits

581

(M)

Cooling fan current was excessive - A/C and Fan Circuits

582

(O)

Open cooling fan circuit - A/C and Fan Circuits

583

(M)

Fuel pump current was excessive - Power / Fuel Pump Circuits

584

(M)

Open power ground circuit - Power / Fuel Pump Circuits

585

(M)

A/C clutch current was excessive - A/C and Fan Circuits

586

(M)

Open circuit in A/C clutch - A/C and Fan Circuits

587

(O, M)

Communication problem between PCM and Variable Control Relay Module (VCRM) - Power / Fuel Pump Circuits

617

(M)

Transmission shift failure (1/2 shift) - Transmissions

618

(M)

Transmission shift failure (2/3 shift) - Transmissions

619

(M)

Transmission shift failure (3/4 shift) - Transmissions

621

(O)

Solenoid/circuit failure - shift solenoid 1 - Transmissions

622

(O)

Solenoid/circuit failure - shift solenoid 2 - Transmissions

624

(O,M)

Solenoid/circuit failure -Electronic Pressure Control (EPC) current is high - Transmissions

625

(O,M)

Solenoid/circuit failure - Electronic Pressure Control (EPC) current is low - Transmissions

626

(O)

Transmission Coast Clutch (CCS) Solenoid/circuit fault - Transmissions

627

(O)

Torque Converter Clutch circuit fault - Transmissions

628

(M)

Excessive converter clutch slippage - Transmissions

629

(O,M)

Torque Converter Clutch circuit fault - Transmissions

631

(O)

Overdrive Cancel Light circuit problem - Transmissions

632

(R)

E4OD - Transmission Control Switch (TCS) should be cycled once between engine ID and Goose test

633

(O)

4x4L switch should be in 4x2 or 4x4 high for the test

634

(O,M)

Park/Neutral Position (PNP) or Clutch Pedal Position (CPP) circuit fault Electronic shift transmission - Manual Lever Position (MLP) sensor out of range in Park-Transmissions

636

(O,R)

Transmission Oil Temperature (TOT) sensor out of range - Transmissions

637

(O,M)

TOT sensor is/was high or open - Transmissions

638

(O,M)

TOT sensor is/was low or grounded - Transmissions

639

(R,M)

Transmission Speed sensor (TSS) circuit fault - Transmissions

641

(O)

Transmission solenoid/circuit failure Shift Solenoid 3 - Transmissions

643

(O,M)

Torque Converter Clutch (TCC) circuit - Transmissions

645

(M)

Transmission 1st gear failure - Transmissions

646

(M)

Transmission 2nd gear failure - Transmissions

647

(M)

Transmission 3rd gear failure - Transmissions

648

(M)

Transmission 4th gear failure - Transmissions

649

(M)

Transmission EPC system failure - Transmissions

651

(M)

Transmission EPC solenoid/circuit fault - Transmissions

652

(O)

Torque Converter Clutch (TCC) circuit fault - Transmissions

654

(O)

Transmission selector not in PARK - Transmissions

656

(M)

Torque Converter Clutch (TCC) slip - Transmissions

657

(M)

Transmission temperature was excessive - Transmissions

Description of the standard trouble OBD codes by family

Ford Error Code P0430

Standard or generic fault codes are a list of codes common to all manufacturers.
This list of faults, also called DTC (for Data Trouble Code) has been defined so that any diagnostic device can read and decode them. They have a standard format as shown below:

The first letter indicates the family of DTC.

Microsoft Error Codes

  • P: Powertrain, (i.e. engine and gearbox)
  • C: Chassis
  • B: Body
  • U: User network

The first digit indicates if the code is generic or not (green digit):

Ford Error Codes P0401

  • 0: Generic fault
  • 1: Manufacturer fault

As the list of generic OBD codes is not always sufficient, manufacturers can add as many of their own codes as they need.

The last 3 digits correspond to an incremented number (purple digits).
This may be a hexadecimal number (i.e. from 0 to 9 + from A to F). For P family codes, sub-families have been defined using the 1st digit (in this example the '3'):

  • 0 , 1 and 2: for the air/fuel mixture
  • 3 : for the ignition system
  • 4 : for checking auxiliary emissions
  • 5 : for engine idling
  • 6 : for the onboard computer and ancillary outputs
  • 7, 8 and 9: for the transmission (gearbox)
  • A, B and C : for hybrid propulsion

Error Code List

These OBD codes were standardized using SAE J2012 and ISO 15031-6 standards which, to our knowledge, contain about 11 000 definitions in the most recent version.

Ford Error Codes Sensor Circuit

Below you will find a list of the most commonly used codes. Our software contains all of the 11 000 codes. Don't hesitate to download it. It is free and, using an ELM327 or ELM323 interface, can be used to read the fault codes. For more details, go to our EOBD-Facile car diagnostic software page.

Select the family of the DTC (OBD codes)